產品介紹
產品定位與應用：NoiseKen ESS-B3011A 搭配 GT-30RA 為 30 kV 靜電放電模擬器，可執行 EN／IEC 61000-4-2 與 ISO 10605 相關測試配置；適合 ESD 抗擾度驗證、研發與品保測試。此型號已停止生產，實際交付前須確認配置、狀態與校正需求。
選型確認重點：評估 ESS-B3011A + GT-30RA 時，建議同步確認測試規範、放電網路、放電尖端、接地方式、附件、校正狀態與交期。
採購與技術確認：弘燁科技可依實際測試條件、設備狀態與附件組合，協助確認可交付配置及同級替代方案。
規格
規格重點
| 輸出電壓 | 0.20 kV 至 30.0 kV，最大 30.5 kV |
|---|---|
| 設定解析度 | 0.20 至 10.0 kV 為 0.01 kV；10.0 至 30.0 kV 為 0.1 kV |
| 電壓允差 | 0.20 至 1.99 kV：±10%；2.00 至 30.0 kV：±5% |
| 放電模式 | 接觸放電與空氣放電 |
| 重複週期 | 0.05 至 9.99 秒，或 10.0 至 99.9 秒／手動 |
| 對應規範 | EN／IEC 61000-4-2、ISO 10605 |
| 充電與電源 | 本體充電電阻 10 MOhm；AC 100 至 240 V，62 VA |
| 尺寸與重量 | 主機 270 × 263 × 200 mm，約 4.6 kg；放電槍約 1080 g |
典型應用
- ESD 抗擾度測試與驗證
- 車用與消費性電子靜電放電測試
- 研發、品保與失效分析測試準備
- 核對 GT-30RA、CR 單元、附件與校正狀態
檔案下載
原廠英文說明
Product positioning and application: The NoiseKen ESS-B3011A with GT-30RA is a 30 kV ESD simulator for EN/IEC 61000-4-2 and ISO 10605 related test configurations. This discontinued model requires configuration, condition and calibration review before supply.Configuration review: Confirm the test standard, discharge network, discharge tip, grounding, accessories, calibration status and delivery requirement before quotation. SMART can help compare available configurations.Key SpecificationsDischarge voltage0.20 kV to 30.0 kV, 30.5 kV maximumSetting resolution0.01 kV from 0.20 to 10.0 kV; 0.1 kV from 10.0 to 30.0 kVVoltage tolerance0.20 to 1.99 kV: +/-10%; 2.00 to 30.0 kV: +/-5%Discharge modesContact discharge and air dischargeRepetition cycle0.05 to 9.99 seconds, or 10.0 to 99.9 seconds/manualStandards supportEN/IEC 61000-4-2 and ISO 10605Charging and power10 MOhm main-unit charging resistor; AC 100 to 240 V, 62 VADimensions and weightMain unit 270 x 263 x 200 mm, approximately 4.6 kg; discharge gun approximately 1080 gTypical ApplicationsESD immunity testing and validationAutomotive and consumer-electronics ESD testingR&D, QA and failure-analysis test preparationGT-30RA, CR unit, accessory and calibration review