產品介紹
產品定位：Anritsu MS9740A 光學頻譜分析儀｜Optical Spectrum Analyzer (OSA)｜MS9740A 屬於頻譜分析與射頻訊號量測設備，可用於RF 訊號分析、雜訊量測、通訊測試、EMI 預掃描、研發除錯與產線檢測。
選型重點：實際頻率範圍、動態範圍與分析功能需依機身選配與校正狀態確認。評估 MS9740A 時，建議同步確認頻率範圍、RBW/VBW、前置放大器、追蹤產生器、相位雜訊、選配與校正狀態。
採購與技術確認：弘燁科技可依目前庫存、附件組合、校正需求與交期，協助比對同級替代型號並整理可交付方案。
品牌與分類：品牌為 Anritsu，產品分類為 射頻微波儀器。如需確認完整規格、附件、校正與交期，建議提供實際量測條件由 SMART 協助確認。
規格
原廠完整規格表 / Full Specifications
以下整理原廠完整規格表，供型號確認、規格比對與詢價確認使用。
SpecificationsDetails
10 μm/125 μm SM fiber (ITU-T G.652), 50 μm/125 μm GI fiber 10 μm/125 μm SM fiber (ITU-T G.652), 50 μm/125 μm GI fiber, 62.5 μm/125 μm GI fiber
User replaceable: FC, SC, ST, DIN
Wavelength measurement range
±20 pm (1520 nm to 1620 nm, Resolution: 0.03 to 0.2 nm)*1, *2 ±100 pm (1520 nm to 1620 nm, Resolution: 0.5, 1.0 nm)*1, *2 ±50 pm (1530 nm to 1570 nm, Resolution: 0.07 to 0.2 nm)*3, *4
±100 pm (1530 nm to 1570 nm, Resolution: 0.5, 1.0 nm)*3, *4
0.03, 0.05, 0.07, 0.1, 0.2, 0.5, 1.0 nm
0.07, 0.1, 0.2, 0.5, 1.0 nm
| High dynamic range | 60 dB (0.4 nm from peak wavelength)*1 |
|---|---|
| Normal dynamic range | 58 dB (0.4 nm from peak wavelength)*1 |
| [Resolution | 0.05 nm, 1550 nm, Optical ATT: Off, 20° to 30°C] |
| High dynamic range | 60 dB (0.5 nm from peak wavelength)*3 |
| Normal dynamic range | 58 dB (0.5 nm from peak wavelength)*3 |
| [Resolution | 0.07 nm, 1550 nm, using SM fiber, Optical ATT: Off, 20° to 30°C] |
| Sweep width | 0.2 nm to 1200 nm, 0 nm |
|---|---|
| Sweep speed | ≤0.2 sec. (Span 5 nm) |
| [Resolution | 0.1 nm, VBW=10 kHz, Normal dynamic range, center 1550 nm, sweep start to stop, no optical input, sampling point: ≤501] |
426 (W) × 177 (H) × 350 (D) mm (excluding projections) ≤15.0 kg (without option) *1: Using SM fiber (ITU-T G.652), after 2 hours of warm-up (the Repeat sweeping performed at Span 100 nm or more and VBW 10 kHz or more during the warm-up operation), after Auto Align, at stable room temperature.
*2: Built-in option 002, after Wl cal (ref) wavelength calibration execution, at stable room temperature. *3:
Warm-up the instrument for at least 2 hours before measurement by performing repeated sweeping at span ≥100 nm, VBW = 10 kHz. Perform waveform calibration after auto-optical alignment (WI Cal) and keep the instrument at the same temperature unless stated otherwise. Use either SM fiber (ITU-T G.652) or GI fiber (50 μm/125 μm) with a return loss of >40 dB, or GI fiber (62.5 μm/125 μm) with a return loss of >38 dB. *4: Built-in MS9740A-002, after Wl Cal (Ref), with SM fiber.
原廠英文說明
- Measurement of passive optical devices in <0.2s(5nm) reduces total analysis time
- Dedicated applications for evaluating active optical devices
- Excellent cost performance
- Dynamic range performance ≥60 dB (0.4 nm from peak wavelength)
- 30 pm minimum resolution bandwidth
- Supports SM and MM fibers
- Lightweight, 50% less power consumption